Sterile rat-tail type I collagen (2.06 mg ml-1; First Link, Birmingham, UK) and 10 vol/vol 10x Minimum Essential Medium (Life Technologies, Ltd., Paisley, UK). After neutralisation, the final 10 vol/vol hCEC medium was added. This solution was then left on ice for 30 min to prevent gelling while allowing dispersion of any small bubbles within the solution before casting in well plates.Plastic Compression of Collagen GelsCollagen gels were plastic compressed using a confined flow compression method. A volume of 2.2 ml of collagen solution was added to each well of a 12 well plate (Nunc; Fisher, Loughborough, UK). Well plates were incubated at 37uC for 30 min to allow the collagen to undergo fibrillogenesis. 23727046 Once the gels were set they were subjected to a confined compression (Fig. 1). Briefly, a sterile nylon mesh and a sterile filter paper circle were placed directly on top of a collagen gel and then a chromatography paperFigure 1. Plastic compression process. Schematic diagram showing the confined flow plastic compression process in a 12 well plate format to create RAFT. doi:10.1371/journal.pone.0050993.gPC Collagen for Endothelial TransplantationFigure 2. Loading and insertion of RAFT into an ex vivo porcine eye using Tan EndoGlideTM. Representative photographs showing the process of loading (A ) of the Tan EndoGlideTM with RAFT construct and insertion (E ) of RAFT into the anterior chamber of an ex vivo porcine eye model. (A) Loading forceps grasp the edge of the RAFT construct from the spatula. (B) RAFT is pulled into the cassette and (C) automatically coils into a double coil AZP-531 chemical information configuration. (D) RAFT is fully loaded into the cassette with no upper surfaces touching. (E) Tan EndoGlide TM is inserted into the anterior chamber that is prevented from collapsing using a column of saline via an inserted needle. (F) RAFT is pulled from the cassette (G) into the anterior chamber and positioned centrally before (H) an air bubble is inserted to appose RAFT to the posterior cornea. doi:10.1371/journal.pone.0050993.groll was added. A 35 g load was then applied to the system for 15 min to allow compression of the collagen gel with loss of fluid in a confined, upward flow direction through the paper roll. This process yielded a thin collagen construct, that we have termed RAFT, which was then either kept in place in a 12 well plate for hCECL culture or trephined using a 8.25 mm trephine (Coronet, Network Medical Products Ltd., Ripon, UK) to obtain small discs for hCEC culture. The trephined discs were transferred to an organ culture dish (Falcon; BD Biosciences, Oxford, UK) and maintained in a small amount of PBS until cell seeding. The thickness of representative RAFT constructs was then measured using optical coherence tomography (OCT) with an anterior segment lens (Spectralis, Heidelberg Engineering, Hemel Hempstead, UK). Thickness was measured at 3 positions along the length of a scanned area in the centre of each of three replicate constructs.Seeding of Endothelial Cells onto RAFTRAFT constructs were coated with either FNC coating mix or CS/L and then hCECLs were seeded onto the surface in 12 well plates at a density of 2000?000 cells/mm2 in a volume of 2 ml medium. Primary hCECs were seeded onto FNC coated RAFT discs in organ culture AZP-531 site Dishes at a density of 2000?000 cells/mm2 in a volume of 20 ml. Several hours later, after cells had attached, wells were flooded with endothelial cell culture medium. Dishes were placed in an incubator at 3.Sterile rat-tail type I collagen (2.06 mg ml-1; First Link, Birmingham, UK) and 10 vol/vol 10x Minimum Essential Medium (Life Technologies, Ltd., Paisley, UK). After neutralisation, the final 10 vol/vol hCEC medium was added. This solution was then left on ice for 30 min to prevent gelling while allowing dispersion of any small bubbles within the solution before casting in well plates.Plastic Compression of Collagen GelsCollagen gels were plastic compressed using a confined flow compression method. A volume of 2.2 ml of collagen solution was added to each well of a 12 well plate (Nunc; Fisher, Loughborough, UK). Well plates were incubated at 37uC for 30 min to allow the collagen to undergo fibrillogenesis. 23727046 Once the gels were set they were subjected to a confined compression (Fig. 1). Briefly, a sterile nylon mesh and a sterile filter paper circle were placed directly on top of a collagen gel and then a chromatography paperFigure 1. Plastic compression process. Schematic diagram showing the confined flow plastic compression process in a 12 well plate format to create RAFT. doi:10.1371/journal.pone.0050993.gPC Collagen for Endothelial TransplantationFigure 2. Loading and insertion of RAFT into an ex vivo porcine eye using Tan EndoGlideTM. Representative photographs showing the process of loading (A ) of the Tan EndoGlideTM with RAFT construct and insertion (E ) of RAFT into the anterior chamber of an ex vivo porcine eye model. (A) Loading forceps grasp the edge of the RAFT construct from the spatula. (B) RAFT is pulled into the cassette and (C) automatically coils into a double coil configuration. (D) RAFT is fully loaded into the cassette with no upper surfaces touching. (E) Tan EndoGlide TM is inserted into the anterior chamber that is prevented from collapsing using a column of saline via an inserted needle. (F) RAFT is pulled from the cassette (G) into the anterior chamber and positioned centrally before (H) an air bubble is inserted to appose RAFT to the posterior cornea. doi:10.1371/journal.pone.0050993.groll was added. A 35 g load was then applied to the system for 15 min to allow compression of the collagen gel with loss of fluid in a confined, upward flow direction through the paper roll. This process yielded a thin collagen construct, that we have termed RAFT, which was then either kept in place in a 12 well plate for hCECL culture or trephined using a 8.25 mm trephine (Coronet, Network Medical Products Ltd., Ripon, UK) to obtain small discs for hCEC culture. The trephined discs were transferred to an organ culture dish (Falcon; BD Biosciences, Oxford, UK) and maintained in a small amount of PBS until cell seeding. The thickness of representative RAFT constructs was then measured using optical coherence tomography (OCT) with an anterior segment lens (Spectralis, Heidelberg Engineering, Hemel Hempstead, UK). Thickness was measured at 3 positions along the length of a scanned area in the centre of each of three replicate constructs.Seeding of Endothelial Cells onto RAFTRAFT constructs were coated with either FNC coating mix or CS/L and then hCECLs were seeded onto the surface in 12 well plates at a density of 2000?000 cells/mm2 in a volume of 2 ml medium. Primary hCECs were seeded onto FNC coated RAFT discs in organ culture dishes at a density of 2000?000 cells/mm2 in a volume of 20 ml. Several hours later, after cells had attached, wells were flooded with endothelial cell culture medium. Dishes were placed in an incubator at 3.
